How to Reset Whirlpool Washing Machine [Full Guide]

How to Reset a Whirlpool Washing Machine

Reset a Whirlpool washing machine, you can follow these steps:

Unplug the washing machine from the power source or turn off the circuit breaker that supplies power to the appliance.
Wait for approximately one minute to allow the machine to fully power down.
Plug the washing machine back into the power source or turn on the circuit breaker.
Press and hold the “Cancel” or “Stop” button on the control panel for about three seconds.
Release the button and wait for a few seconds to see if the machine resets.
If the machine doesn’t reset, repeat the process by unplugging it again, waiting for a minute, and then plugging it back in.
Once the machine has successfully reset, you can select a new cycle and start a new wash load.

It’s important to note that the specific steps for resetting a Whirlpool washing machine may vary depending on the model. Consulting the user manual for your particular machine can provide detailed instructions on how to reset it properly.

Resetting a Whirlpool washing machine involves a few simple steps. First, turn off and unplug the machine, then wait for a few minutes. Next, plug it back in and turn it on. Finally, press and hold the “Start” or “Reset” button until the machine resets. Following these key takeaways will help you successfully reset your Whirlpool washer and get it back to working order.

Is There a Reset Button on a Whirlpool Washer?

When it comes to resetting a Whirlpool washer, you might be wondering if there is a dedicated reset button. However, unlike some other appliances, Whirlpool washers typically don’t have a specific reset button. Instead, the reset process involves a combination of actions to restore the machine to its default settings or resolve any issues. By following the steps mentioned earlier for resetting a Whirlpool washer, you can effectively address common problems and get your appliance back on track.

How To Reset a Whirlpool Washing Machine

Resetting a Whirlpool washing machine is a straightforward process that can help resolve various issues. To reset a Whirlpool washer, follow these steps:

Unplug the washer from the power outlet and wait for a few minutes.
Plug the washer back into the power source.
Open and close the washer’s lid six times within 12 seconds. This should activate the reset mode.
The washer will enter a diagnostic test cycle, indicated by a series of beeps or lights flashing.
Allow the diagnostic cycle to complete, and the washer will reset to its default settings.
By performing these steps, you can reset a Whirlpool washing machine and potentially resolve problems such as error codes, malfunctions, or unresponsive controls. Remember to consult the specific instructions provided in your appliance’s manual for accurate resetting steps tailored to your model.

1. Unplug the Washer

To reset a Whirlpool washer, follow these steps:

Unplug the washer from the power source. This will disconnect it from the electrical supply.
Wait for a few moments. This allows the washer to completely power down and reset itself.
Plug the washer back in. Ensure that it is securely connected to the power source.
Check the control panel. The washer should display the default settings or be ready for a new cycle.
Proceed with using the washer as normal. You can select the desired settings and start a new wash cycle.

Resetting the washer by unplugging it helps resolve minor issues or errors that may have occurred. If the problem persists or if you require further assistance, consult the manufacturer’s instructions or reach out to a professional technician.

2. Reset the Circuit Breaker

Sure! Here’s a shorter explanation of how to reset a Whirlpool washing machine:

Unplug the washer from the power outlet.
Reset the circuit breaker by switching it off and waiting for 10-15 seconds.
Switch the circuit breaker back on.
Plug in the washer.
Test the washer to see if the reset resolved any issues.

If the problem persists, consult a professional or refer to the manufacturer’s instructions.

3. Press Buttons

To reset a Whirlpool washer, you can try the following steps:

Press and hold the “Power” button on the control panel. This will turn off the washer.
Release the “Power” button and then press and hold the “Start” or “Cancel” button for a few seconds.
Wait for the washer to power down and reset. This may take a few moments.
Once the washer has reset, you can release the button and proceed with using the washer as normal.

Please note that the specific buttons and reset process may vary depending on the model of your Whirlpool washer. Consult the user manual or check Whirlpool’s official website for detailed instructions specific to your model.

If the problem persists or if you need further assistance, it is recommended to contact Whirlpool customer support or a qualified technician for help.

4. With the Dial

To reset a Whirlpool washer with a dial control:

Turn the dial to the “Off” position to ensure the washer is powered off.
Unplug the washer from the power outlet and wait for about 30 seconds.
Plug the washer back in and turn the dial to the desired cycle or program.
Press and hold the “Start” button until the washer starts the cycle. This will initiate the reset process.
Allow the washer to complete the cycle and check if the issue is resolved.

If the problem persists or if you need further assistance, it is recommended to consult the user manual or contact Whirlpool customer support for specific instructions and troubleshooting guidance for your particular model of washer.

5. Open and Close the Lid

To reset a Whirlpool washer with a lid control:

Open the lid of the washer and ensure it is fully open.
Unplug the washer from the power outlet and wait for about 30 seconds.
Plug the washer back in and close the lid securely.
Set the desired cycle or program using the control panel.
Press and hold the “Start” button until the washer starts the cycle. This will initiate the reset process.
Allow the washer to complete the cycle and check if the issue is resolved.

6. Press Power and Programme

To reset a Whirlpool washer with a digital control panel:

Ensure that the washer is powered off by pressing the “Power” button or turning off the main power switch.
Press and hold both the “Power” button and the “Programme” button simultaneously.
While holding down the buttons, turn on the washer by pressing the “Power” button or flipping the main power switch.
Continue to hold the buttons for a few seconds until the control panel lights up or displays a reset message.
Release the buttons and wait for the washer to reset. This may take a few moments.
Once the reset process is complete, the washer should be ready to use. You can select a new programme and start a new cycle.

If the issue persists or if you require further assistance, it is recommended to refer to the user manual or contact Whirlpool customer support for specific instructions tailored to your model of washer.

7. Reset the Cabrio Touch Screen

To reset the touch screen on a Whirlpool Cabrio washer:

Press and hold the “Power” button on the control panel for at least three seconds to turn off the washer.
Unplug the washer from the power outlet.
Wait for about one minute to allow the washer to fully discharge.
Plug the washer back into the power outlet.
Press the “Power” button to turn on the washer.
Touch the screen to navigate through the settings or select a new cycle.

By following these steps, you can reset the touch screen on your resetting a Whirlpool washer. If the issue persists or if you need further assistance, it is advisable to consult the user manual or contact Whirlpool customer support for more specific guidance related to your particular model of washer.

Whirlpool Washer Troubleshooting

To troubleshoot common issues with your resetting a Whirlpool washer, follow these steps, including resetting the washer if needed:
Check power supply and water connections.
Ensure the door/lid is closed securely.
Reset the washer by unplugging it for a few minutes and then plugging it back in.
Consult the user manual for specific troubleshooting guidance.
Contact Whirlpool support or schedule a service appointment if issues persist.

Why is My Whirlpool Washer Not Turning On?

If your Whirlpool washer is not turning on, there could be various reasons for this issue. Before attempting to reset the washer, make sure to check the power supply, outlet, and circuit breaker to ensure they are functioning properly. If everything seems fine with the power source, try resetting the washer by unplugging it for a few minutes and then plugging it back in. This can help reset any potential electrical glitches. If the washer still does not turn on after resetting, it may require further troubleshooting or professional assistance from Whirlpool support.

Why Does My Whirlpool Washer Stop Mid Cycle?

To troubleshoot a Whirlpool washer that stops mid-cycle, try resetting the washer by unplugging it for a few minutes and then plugging it back in. If the issue persists, check for clogged hoses, unbalanced loads, or contact Whirlpool support for assistance.

Washer timer: To reset the washer timer on a Whirlpool washer, follow these steps:

Unplug the washer for 1-2 minutes.
Plug it back in.
Open and close the lid.
Select a cycle and settings.
Start the washer and observe if the timer advances properly.

Control board:To reset the control board on a Whirlpool washer, you can try the following steps:

Unplug the washer from the power source.
Wait for a few minutes to allow the control board to fully discharge.
Plug the washer back in.
Press and hold the “Start” or “Cancel” button on the control panel for 5-10 seconds.
Release the button and wait for the control board to reset.
Test the washer to see if the issue is resolved.

If the problem persists, it’s recommended to consult the user manual or contact Whirlpool customer support for further assistance.

Door lock motor and switch assembly: To reset a Whirlpool washer involving the door lock motor and switch assembly:

Unplug the washer.
Disconnect and reconnect the wiring harness to the door lock motor and switch assembly.
Close the washer door.
Plug the washer back in and turn it on.

For further assistance, consult the user manual or contact Whirlpool customer support.

Water inlet valve: To reset a Whirlpool washer, follow these steps involving the water inlet valve: unplug the washer, clean the inlet valve screens, reconnect the water hoses, and plug the washer back in.

Clogged hose: If you suspect a clogged hose is causing issues with your Whirlpool washer, try the following steps to reset it: unplug the washer, disconnect the hoses, inspect them for any blockages or debris, clean or replace the hoses if necessary, and reconnect them securely before plugging the washer back in.

Pump and motor: If you’re experiencing problems with your Whirlpool washer related to the pump and motor, resetting the washer may help. To do this, first, unplug the washer from the power source. Then, locate the pump and motor assembly, which is usually at the bottom of the machine. Check for any obstructions or debris that may be affecting the proper functioning of the pump and motor. Clear any clogs or remove any objects that you find. Once the area is clear, plug the washer back in and try running a cycle to see if the issue is resolved.

Why is My Whirlpool Washer Not Washing Properly?

If your Whirlpool washer is not washing properly, resetting the washer can sometimes help address the issue. Begin by unplugging the washer from the power source. This will allow the washer’s electronics to reset. After a few minutes, plug the washer back in. Next, check the water supply and ensure that the inlet hoses are not clogged or kinked. Additionally, inspect the detergent dispenser and make sure it is clean and free from any residue or blockages. Finally, run a diagnostic cycle or select a different wash cycle to see if the problem persists. If the issue continues, it may be necessary to contact a professional technician for further assistance.

Wrong temperature: To address improper washing in a Whirlpool washer, try resetting the machine by unplugging it for a few minutes and then plugging it back in. Ensure that the temperature settings are correct and that the water supply is delivering hot water. If the issue continues, check the water inlet valve or consult the user manual. Consider seeking professional assistance if needed.

Hoses aren’t connected properly: Ensure hoses are properly connected for optimal washing performance. Reset washer if needed.

Your washing machine is dirty: To address a dirty washing machine, consider resetting Whirlpool washer and following a cleaning routine to maintain its cleanliness and performance.